Deye-based 8 kW set - Hybrid solar + battery
Residential catalogue range · Hybrid solar and battery
A proposed solar-and-storage package designed around selected daytime loads and an assessed backup requirement. Solar generation, battery charging and backup operation depend on the final approved system design. Proposed reseller configuration, not a factory Deye kit. Final equipment, compatibility and quantities require a written quotation and engineering assessment.
Proposed specifications and contents
- Inverter proposal: 1 × Deye SUN-8K-SG05LP3-EU-SM2; catalogue output class 8 kW. Confirm the exact nameplate, operating conditions and AC output limits before selection; backup and surge ratings apply only where supported by that model.
- AC configuration: three-phase inverter family. Confirm the required site voltage/frequency and, for three-phase installations, each phase’s load and output limit.
- PV proposal: 18 × third-party 550 W panels = 9.9 kWp nameplate array capacity. Panel manufacturer/model is not selected; voltage, current, dimensions and string layout remain unconfirmed. This is a proposed quantity, not a validated minimum string size.
- Storage proposal: 3 × Deye SE-G5.1 Pro-B batteries, each LiFePO4, 51.2 V nominal, 100 Ah and 5.12 kWh nominal; total 15.36 kWh nominal. Nominal energy is not guaranteed usable AC energy or runtime. BMS communication and battery/inverter compatibility must be confirmed.
- Balance of system (BOS): allowance only, not a confirmed itemised supply list. Final design must identify mounting rails/clamps, PV cabling/connectors and DC isolation/protection, battery cables, fuses/breakers, busbars and communication leads, AC isolation/protection, earthing and any required metering/monitoring.
Benefits and intended use
Combines daytime solar generation with stored energy for selected loads. Separating essential from non-essential circuits helps target the available backup capacity.
Consider for assessed household essential circuits such as lighting, communications, computers and selected refrigeration. Appliance names are examples, not a promise that every appliance can operate together. Do not assume suitability for medical/life-support or other safety-critical loads without a specialist design.
Minimum requirements before ordering
- Provide an appliance/load schedule with watts, operating hours, simultaneous demand and motor starting loads. For backup/off-grid operation, inverter continuous and surge output must cover the selected loads within model and per-phase limits. For grid-only operation, size solar to daytime demand and the approved connection capacity; 8 kW is not a promise of whole-site coverage.
- Size the battery bank for BOTH energy and discharge power. Required usable AC energy (kWh) = average backed-up load (kW) × required backup hours. Required nominal battery energy must also allow for permitted depth of discharge, reserve and conversion losses. Confirm that aggregate battery current, BMS limits, inverter limits and cables support the load; the proposed 3-battery bank is not a guaranteed minimum for every application.
- Determine the minimum panels per string using the selected panel’s temperature-adjusted voltage, inverter start-up voltage and MPPT operating window. Check maximum cold-weather open-circuit voltage, operating/short-circuit current and permitted PV power before fixing series/parallel quantities. Array kWp alone does not establish compatibility.
- A qualified installer must verify structural support, shading and PV mounting, equipment environment, ventilation, protection, earthing, safe isolation and commissioning. Do not install or expand from this catalogue description alone.
Expansion to match your requirements
- For longer backup time, assess additional compatible battery modules. Each additional SE-G5.1 Pro-B contributes 5.12 kWh nominal, but permissible combinations, firmware, communication, protection and current sharing must be checked. More battery energy does not increase the inverter’s AC output rating.
- For more daytime energy, assess extra panels and roof/ground space, then recalculate the complete string layout against the inverter limits. More panels do not automatically increase AC output or guarantee off-grid autonomy.
- For higher simultaneous loads, assess a larger inverter or manufacturer-supported parallel design. Do not assume all models can be paralleled or that different inverter models can be mixed. Reassess phase balance, batteries, cabling, protection and charging capacity.
Quotation and exclusions
For sizing, provide your location, supply phase, appliance list, daily use, required backup hours, existing equipment and future expansion plans. Contact sales@solitecpng.com or +675 70868277.
Catalogue set reference: SET-8-13.
Manufacturer specification references: SE-G5.1 Pro-B battery; SG05LP3 inverter family. Confirm the supplied revision before ordering.
Choose a proposed configuration for quotation
These are planning targets, not installed specifications or guaranteed model options. Each link opens an email enquiry, not a priced checkout configuration. Solitec must validate the final bill of materials.
-
Essential loads: Assess the proposal for selected lighting, communications and other essential loads. Supply peak watts, daily energy and backup hours. Request this profile by email
-
Extended autonomy: Reassess compatible storage AND recharge capacity for actual local solar conditions and required autonomy. Request this profile by email
-
Higher-power loads: Reassess inverter/phase, battery discharge and starting loads. More panels or battery kWh alone do not raise inverter output. Request this profile by email